Search result for:  WA 0852 2611 9277 Design Interior Kamar Lesehan Apartment Park View Condominium Detos Depok

... table or Mini. Recall that the tail-ball is always located at the head-ball's Theta + Pi, and 1 - head-ball's Rho. From there you should be able to figure out the analogous head ball Parking tracks. However - we are not recommending doing so. I WAs initially excited when I discovered the ability to add 2-ball function, and the WAy it can produce very nice patterns with some algorithmic tracks. And the ball Park is Designed symmetrically because head-ball Parking WAs planned. But we've recently stopped shipping with 2-ball mode, and are moving away from of ...

@mahorlick - Hard to know what WAs the specific cause of both balls being together - but almost certainly could not be related to which track you played. More likely, sand may have built up around the "ball-park" (barrier under the shade ring where the second ball is Parked and picked up). This can prevent the second ball from going all the WAy into the Park - if so, it can accidentally be picked up by the main ball as it goes by. There's no automated WAy of separating them - so the fix is removing the glass and doing it manually. Make sure you brush the sa ...

Hi Hunter - You are not the only one who would prefer the LED shield ring to be smaller, and not overlap the sand field so much. The Design process in making this choice WAs a compromise between showing as much of the sand as possible vs. minimizing the potential for direct line of sight to the LED's (which can be very distracting from across a room). This is very angle dependent - not a factor when looking straight down on the table, but is while seated 3+ meters away - especially with the end table version, since it's LEDs are significantly higher than t ...

Simple question on orientation of the Designs that are not symmetric - what is the correct "top" point to use as the bottom and top of the Design? I assume that the 0,1 point is the "top" of the table and base the Design off that reference point. I have seen in the tracks that are in the Library that there is a range of choices - the face and serpent Designs have a different base than the sailboat. I have written programs that can output a Design in any angle, but I wonder if there are "rules" that should be set or followed. Any comments?

Fora metal coffee table (36" diameter), the configuration setting is RGBW 2-ball (NOT servo). The radius should be set to 13.5. The purpose of the ball Park piece is to provide a WAy to purposely cleave the tail ball from the tail magnet (which is called "parking"). This happens when you play the special track "detach" and allows you to go from 2-ball play to 1-ball. The ball stays Parked until you play "attach". The placement of the ball Park is important - follow the directions carefully.

If i run the erase track and the ball stops in the middle, i usually pick a track that looks like it will start from the middle. Its disappointing when the ball travels across the table to the edge to start the Design...leaving the ugly path on the final Design. The same thing happens if the ball is stopped on the edge..if i WAnt it to start making the Design on the edge, sometimes it will go to the center. How or can i choose the balls starting point for a Design??

@gerardo1992lopezgmail-com ... it WAs in the Approval queue. It should be there now. Look under artists for my tracks: "adambrower".

@adambrower thank you so much! For whatever reason when I search it doesn't pop up :/

no problem, and no pay is necessary. look in community tracks for "big-tupac-work". Attachment :  Screen-Shot-2023-11-28-at-5.35.31-PM.png

Hi, looking for someone to make a custom tupac track. Willing to pay a fee.Thanks!

Shoot me an email at [email protected] have a great day.

Willing to pay if needed/desired just don’t know how to make custom Designs and WAnt it done well

... table with RGBW lights. -> Should i use the (SERVO, 2 ball edition), or the (2 ball edition) Also, the RADIUS field is blank. I noticed on the tutorial video, this field had 8.25" entered. What is the correct value for this? When i leave it blank i am getting the ball trapped in the ball Park WAy too often. Finally - What is the purpose of the "Ball Park" Piece? Is it really needed? Thanks!

@Bruce - So I decided to play around with creating a track after logging into my table and seeing the rho, theta coordinates for the "tail" attach and detach tracks. Using those as a guide, I WAs able to create tracks that utilize the other side of the ball Park. Both have worked perfectly after multiple runs. AttachMain is attached below. **Note: I ran them with the tail ball already attached. I'm sure that both balls in the ball Park could be problematic for the magnets.** Attachment : AttachMain.thr

This just in from our developer, Matt: My first guess is that he already has his own tracks downloaded. The default filters show only tracks you have not yet downloaded. If he goes to the hamburger icon (three lines) and switches the filter to "All Tracks", does that show his own again? Tracks you've already downloaded will have the green checkmark next to them. Matt

AFAIK you cannot View files downloaded from community portal? But, I don't think the appearance is a table size issue, I don't think it's even completing the track, is it supposed to end mid table like that? I didn't think that WAs an option. Maybe the download WAs corrupt. I haven't gone full diagnosis on it.

... of your Sisyphus Set the IP address of the Sisyphus to fixed Tasker Task Set up (purchase may be required) In Tasker, create a 'HTTP Post' action for each Sisyphus task (I've set pause, play, sleep and WAke) in Server:Port field: enter the sisyphus request, see the following documentation to determine what to put in (Thanks @safepassagedesign) and ensure you replace the IP address with the fixed address you set for your table In the Data / File field: if X is listed in the documentation put {"data":X}, so if the documentation asks for {} enter {"data": ...

... the update will complete and the table will reboot. As soon the ball begins to move UNPLUG your table. WAit 30 seconds and plug the table back. You can now operate the table as desired. What may happen if you do not power-cycle your table after the update - The ball will fail to return to the center and begin operating in the wrong position. This is likely to result in one of the scenarios below: The motors will fault, showing a notification that there WAs a hardware failure. If this does happen, you do not need to worry about damage to your table. Just ...

Is there a track that displays what our tables can do in a short amount of time? We live in a retirement community and people ask if they can come and WAtch our table. The problem I am running into is I may be running a Design that takes a few hrs or doing an erase. Id like to have something where I could run a 10 min Design that shows something interesting for them to WAtch. Perhaps a track that just goes around the perimeter of the table so the Design in the middle is not disturbed. They all WAnt to see the ball move. We have a few Designs we keep all da ...

I like it!!